Should a heat pump run all the time?
For homeowners accustomed to a gas or oil boiler, the answer can initially seem strange.
A traditional boiler is often programmed to switch on for a few hours in the morning, turn off during the day, and then run again in the evening.
A heat pump can work differently.
Rather than producing a large amount of high-temperature heat for short periods, an air-to-water heat pump can often maintain comfort more effectively by operating for longer periods at a lower heating-water temperature.
However, “leave the heat pump on” does not mean that the compressor must run continuously at full power, 24 hours a day.
Modern inverter heat pumps can adjust their output as heating demand changes. The controller can also stop the compressor when there is no demand.
The real question is therefore:
Should the heating system remain enabled for extended periods, or should it be switched completely off overnight and reheated later?
For many installations, a moderate night setback can provide a useful balance.
Why Heat Pumps Often Run for Long Periods
A heat pump moves heat from outdoor air into the building.
Its efficiency depends partly on the temperature difference it must overcome.
If the heating system can maintain comfort using relatively low-temperature water, the compressor generally faces less demanding operating conditions than when it must rapidly produce much hotter water.
This is one reason heat-pump systems are often designed around:
- longer operating periods;
- relatively stable indoor temperatures;
- weather-compensated flow temperatures;
- inverter modulation;
- gradual changes rather than rapid heating and cooling.
Long runtime therefore does not automatically mean high electricity consumption.
A compressor running steadily at reduced output may be operating exactly as the system designer intended.
By contrast, repeated short start-stop cycles can indicate a different problem. Our guide to heat pump short cycling explains that distinction in detail.
What Does “Running All the Time” Actually Mean?
There are two different concepts that are often confused.
Heating enabled continuously
The heating system remains available throughout the day and night.
The controller decides when the compressor needs to operate and how much output is required.
Compressor running continuously
The compressor itself remains active without stopping.
These are not the same thing.
A heat pump left enabled can:
- increase compressor speed when demand rises;
- reduce output as the building approaches its target temperature;
- stop when no additional heat is required;
- restart when demand returns;
- adjust flow temperature according to outdoor conditions.
The Energy Saving Trust currently recommends keeping heat pumps operating for extended periods and using a setback rather than repeatedly switching heating completely off and back on.
However, the correct control regime still depends on the building and system design.
What Is a Heat Pump Night Setback?
A setback reduces the target indoor temperature during periods when full comfort temperature is unnecessary.
For example, a household might want:
20°C during occupied daytime periods
and a somewhat lower temperature overnight.
Instead of completely disabling space heating, the controller allows the indoor temperature to fall gradually toward the lower target.
Before the occupants wake, the system can return to the normal comfort setting.
The purpose is to avoid maintaining the full daytime temperature when it is not needed, while also avoiding a large morning recovery load.
Why Deep Night Setbacks Can Be Difficult for Heat Pumps
Imagine a house maintained at 20°C during the evening.
At bedtime, the heating is switched completely off.
Overnight, the building cools considerably.
At 06:00, the heat pump is asked to restore the indoor temperature quickly.
At that moment:
- outdoor temperature may be near its daily minimum;
- the building structure is colder;
- room air needs reheating;
- emitters may need more output;
- the controller may request a higher flow temperature;
- domestic hot-water demand may also occur in the morning.
The heat pump therefore faces a large recovery load at potentially demanding outdoor conditions.
By contrast, a moderate setback keeps the building closer to its normal operating condition.
Energy Saving Trust specifically notes that allowing a home to cool several degrees can make the heat pump work harder when reheating it, and recommends extended heating operation with setback as a practical strategy.
Does That Mean You Should Never Turn a Heat Pump Off?
No.
There is no universal requirement to operate every heat-pump system 24 hours a day.
The appropriate schedule depends on:
- building insulation;
- thermal mass;
- emitter type;
- outdoor climate;
- occupancy pattern;
- required indoor temperature;
- heat-pump capacity;
- minimum modulation;
- electricity tariff;
- heating-curve configuration.
The MCS Domestic Heat Pump Guide discusses both continuous and intermittent control strategies and notes that the designer should determine the appropriate control regime for the individual project rather than simply defaulting to continuous operation. (MCS Domestic Heat Pump Guide)
So the objective is not:
“Always run the heat pump 24/7.”
It is:
“Avoid unnecessary large temperature swings and operate the system in a way that matches the building.”

What Happens in a Well-Insulated Home?
A well-insulated building loses heat relatively slowly.
If the indoor target is reduced overnight, the room temperature may fall only slightly.
In that situation, a moderate setback can work particularly well because the heat pump does not need to recover a large temperature difference the following morning.
The building itself acts as a form of thermal storage.
What Happens in a Poorly Insulated Home?
A building with high heat loss may cool much more quickly when heating demand is removed.
A deep overnight shutdown can therefore produce a substantial morning recovery requirement.
The first step is not simply to increase the thermostat.
The correct system design starts with the building’s heat demand, emitter capacity and required flow temperature.
For retrofit projects, these factors should be assessed before deciding how aggressively the temperature should be reduced overnight.
Weather Compensation Makes Continuous Operation Smarter
One of the most important controls in an air-to-water heat-pump system is weather compensation.
Instead of producing the same water temperature regardless of outdoor conditions, the controller changes the target flow temperature as the weather changes.
When it is relatively mild outside, the building loses less heat.
The heat pump can therefore supply cooler water.
When outdoor temperature falls, the controller gradually increases the target water temperature.
This relationship is defined through the heating curve.
Our guide to the heat pump heating curve and weather compensation explains how this works.
Weather compensation can make extended heating operation much more logical because the system is not simply producing maximum-temperature water continuously.
Instead, it attempts to match heat delivery to changing building demand.
Setback and Weather Compensation Work Together
A setback changes the desired indoor condition.
Weather compensation changes the heating-water temperature according to outdoor conditions.
These controls can complement one another.
During normal occupancy, the system follows its configured comfort target and heating curve.
During setback, the indoor target can be reduced.
The heat pump then maintains or restores comfort using the system’s configured control logic.
The exact interaction depends on the controller and installation.
This is why copying another homeowner’s heating-curve or setback values is rarely a good commissioning method.
What About Underfloor Heating?
Underfloor heating has a large heat-transfer area and often contains significant thermal mass.
The floor structure can therefore respond slowly to control changes.
A deep overnight setback may have limited benefit if the floor takes several hours to cool and several more hours to warm again.
For these systems, relatively steady operation can often make sense.
However, the ideal schedule still depends on the building, floor construction and occupancy pattern.
What About Radiators?
Radiators normally respond faster than a large underfloor-heating slab.
This gives the controller more flexibility.
However, heat-pump radiators are often designed to work with lower water temperatures than a traditional boiler system.
That means they may provide heat more gradually.
Large thermostat changes should therefore not be treated exactly like boiler operation.
Does Leaving a Heat Pump On Waste Electricity?
Not necessarily.
A heat pump only uses significant compressor electricity when it is actually required to produce heat.
Leaving the system enabled does not mean it constantly consumes its maximum electrical input.
An inverter heat pump can modulate according to demand.
The more useful questions are:
- What flow temperature is being requested?
- What is the outdoor temperature?
- How much heat is the building losing?
- What compressor output is required?
- Is the unit cycling unnecessarily?
- Is the heating curve correctly configured?
A poorly configured heat pump could use unnecessary electricity even with a sophisticated schedule.
A well-configured system can operate for long periods at moderate output while maintaining stable comfort.
Is Long Runtime a Sign That the Heat Pump Is Undersized?
Not by itself.
Long operating periods can be completely normal.
At cold outdoor temperatures, a correctly sized heat pump may operate for extended periods because the building is continuously losing heat.
This is fundamentally different from a boiler designed to deliver a much higher output for shorter bursts.
The more important question is whether the heat pump:
- maintains the required indoor temperature;
- operates within its declared performance envelope;
- avoids excessive backup-heater use;
- maintains appropriate water flow;
- and operates without abnormal fault conditions.
If the unit cannot satisfy the building load during cold weather, that becomes a sizing and bivalent-system question.
See our guide to heat pump bivalent temperature for the relationship between building demand, heat-pump capacity and supplementary heating.
Can Night Setback Reduce Electricity Consumption?
Potentially, yes.
Reducing indoor temperature reduces the temperature difference between inside and outside.
That lowers building heat loss while the setback is active.
However, part of that saving may later be offset by the energy required to reheat the building.
The final result depends on:
- setback depth;
- setback duration;
- insulation;
- building thermal mass;
- outdoor conditions;
- recovery flow temperature;
- heat-pump efficiency during recovery.
Therefore, there is no universal setback temperature that guarantees the lowest consumption.
The practical objective is to find the lowest setback that remains compatible with comfort and efficient recovery.
What About Dynamic Electricity Tariffs?
A heat pump schedule can also respond to electricity prices.
With a dynamic or time-of-use tariff, it may sometimes make economic sense to shift part of the heating demand into a cheaper period.
Buildings, hot-water cylinders, buffer tanks and other thermal storage can provide some flexibility.
However, aggressive pre-heating can require a higher water temperature and may reduce heat-pump efficiency.
The lowest electricity price does not automatically equal the lowest total heating cost.
Our guide to the dynamic tariff heat pump explains the balance between electricity price, thermal storage, comfort and heat-pump efficiency.
Should You Turn the Heat Pump Off When Leaving Home?
It depends on how long the property will be empty.
For a normal workday, a temperature setback may be preferable to allowing the home to cool substantially.
For a longer absence, a lower target may make sense.
However, minimum-temperature, frost-protection and system-protection functions should remain configured according to the manufacturer’s instructions.
Do not disconnect power from the heat pump merely to stop space heating unless the manufacturer specifically instructs you to do so.
The unit may need power for:
- frost protection;
- pump operation;
- crankcase or component protection;
- controller functions;
- remote monitoring;
- protective routines.
What About Domestic Hot Water?
Space-heating schedules and domestic-hot-water schedules do not necessarily need to be identical.
A hot-water cylinder stores energy, which allows domestic-hot-water production to be scheduled more deliberately.
Depending on the installation, DHW heating may be timed around:
- household usage;
- electricity tariffs;
- PV generation;
- required hygiene cycles;
- available storage capacity.
This creates an opportunity to separate continuous or extended space-heating operation from scheduled hot-water production.
R290 Does Not Determine the Schedule
R290 is the refrigerant inside the sealed refrigeration circuit.
It does not determine whether the heating system should operate continuously or use a setback.
The appropriate schedule depends on the building and complete heating system.
However, modern inverter-driven R290 systems can combine modulation with intelligent controls, weather compensation and smart-energy integration.
Tongyi’s R290 inverter air-to-water heat-pump range supports inverter operation and smart control as part of the wider heating-system design.
The objective remains the same:
provide the heat the building needs without unnecessary temperature lift or unstable operation.
A Practical Heat-Pump Schedule
There is no single timetable appropriate for every home.
A sensible commissioning process is:
- Establish the normal comfort temperature.
- Configure the heating curve correctly.
- Allow the system to operate for several days in representative weather.
- Observe indoor temperature stability.
- Introduce a modest overnight or absence setback if required.
- Monitor how quickly the building cools.
- Observe the morning recovery period.
- Check whether recovery causes unusually high flow temperatures or backup-heater operation.
- Make small adjustments rather than large changes.
- Compare comfort and electricity consumption over similar weather conditions.
This provides much better information than changing the thermostat dramatically from day to day.
Common Heat-Pump Scheduling Mistakes
Treating the heat pump like a gas boiler
Short, high-temperature heating bursts are not necessarily the best operating strategy for a heat pump.
Turning it completely off every night
A deep temperature drop can create a significant recovery load in the morning.
Assuming long runtime means high consumption
Runtime and electricity consumption are not the same measurement.
Increasing the thermostat to heat the house faster
A higher room-temperature setting does not necessarily make the building warm more quickly.
Using an excessively high heating curve for morning recovery
This may increase flow temperature more than necessary.
Changing several control parameters at once
If the schedule, curve and thermostat settings all change together, it becomes difficult to understand what actually improved or worsened performance.
Copying another household’s settings
Two buildings can have very different heat loss, thermal mass, radiators and occupancy patterns.
FAQ
Should a heat pump run all day?
It can be normal and appropriate for a heat-pump system to remain enabled throughout the day. The compressor will still respond to demand and may modulate or stop as required.
Should I turn my heat pump off at night?
Not necessarily. Many installations use a lower overnight setback rather than switching space heating completely off.
What is the best night temperature for a heat pump?
There is no universal temperature. It depends on comfort, building heat loss, thermal mass and how easily the system recovers the following morning.
Is it cheaper to leave a heat pump running?
It depends on the system and control strategy. Extended lower-temperature operation can suit heat pumps well, but the correct schedule should be assessed for the building rather than assumed.
Why does my heat pump run for hours?
Long runtime can be normal, particularly during cold weather. An inverter heat pump may operate for long periods at reduced output rather than repeatedly starting and stopping.
Does a heat pump use full power whenever it is running?
No. An inverter-driven unit can adjust compressor output within its operating range according to demand.
Should I use night setback with underfloor heating?
Potentially, but large setbacks may be less useful with high-thermal-mass floors because the system responds slowly. The schedule should reflect the building and floor construction.
The Takeaway
So, should a heat pump run all the time?
A better way to phrase the question is:
Should the heat pump remain available to maintain the building steadily, or should the heating be repeatedly switched completely off and restarted?
For many air-to-water systems, extended operation combined with weather compensation and a moderate setback can provide a sensible control strategy.
But there is no universal 24/7 rule.
The optimum schedule depends on:
building heat loss + thermal mass + emitters + flow temperature + outdoor temperature + controls + occupancy
A well-designed heat pump should adapt to the building rather than force the building around a rigid timetable.










